27dBm 1700/2100MHz AWS Signal Amplifier

Product Detail

1700/2100MHz AWS Cell Phone signal booster

A signal booster or cell phone repeater is a device used for boosting the cell phone network to the local area by the usage of a reception antenna. In simple words, wireless signal booster is a device to boost the wireless signal and this device make wireless coverage more and more. Wireless repeaters are practical, beautiful and easy to install.Wireless repeaters are designed to meet the needs and requirements of modern citizens. Wireless repeaters come complete with everything necessary for a full cell phone repeater system enabling you to use your cell phone wherever you are. One of the most popular applications of a wireless signal repeater is its use in buildings which are signal isolated. When a house is located too far from the telecom station, which is usually installed around a city, cell phone signal can be very low.



We provides signal boosters kits for any Homes, Offices, Cars, RV's, Boats and more. All amplifier kits come with Indoor and Outdoor Antennas, Cables, Power adapters and more.

HPC-W-27 WCDMA 3G 21mhz repeater Features:

1.With unique appearance design, have good cooling function

2.With MGC function,(Manual Gain Control), Customer can adjust the Gain as needed ;

3.With DL signal LED display, help to install the outdoor antenna at the best state;

4.With AGC and ALC, make repeater work stable . 

5.PCB with isolation function ,make UL and DL signal not influence each other,

6.Low  intermodulation, high Gain ,stable Output power 

HPC-W-27 2100mhz repeater Inside and Outside Design



HPC-W-27  Dual band repeater is to support any two mobile band existing in the world to help end users to improve mobile signals for much better phone call quality and smoother data transmission. It is designed to support coverage area max can up to 2000 square meters with proper engineering. Below are the main features.

1.The consumer repeater is an ideal solution for providing a cost effective improvement in cellular in-building coverage of a home, office, restaurant or building, in the quickest time possible.

2.Manual gain control (MGC) available for both uplink and downlink to adjust the gain value for proper coverage during installation or maintenance.

3.To maintain safe and specific output signal levels and give alarms on self-oscillation, the repeater has built-in AGC and ALC circuits, which can automatically control the gain of the repeater depending upon the strength of input signals.

4.Auto shut off function available for both uplink and downlink to avoid deep self-oscilation from jamming the towers, saving your trouble from operators. 

5.Wide band feature enables all devices operating within the wide frequency range of the repeater to see an improvement in performance.

6.Multiple phones and other handheld devices throughout a building can benefit from a wireless repeater.

7.Supports up to (500) users / calls simultaneously.

8.Extended phone battery life. (Your phone does not need to put out as much power due to improved reception.)

Specification of HPC-W-27 Dual band repeater:

Electrical specification			Uplink	Downlink
Frequency Range	WCDMA 2100		1710 ~ 1755 MHz	2110 ~ 2155 MHz
Max .Gain			= 70dB	= 75dB
Max .Output Power			= 24dBm	= 27dBm
MGC ( Step Attenuation )			= 31dB / 1dB step
Automatic Level Control			= 20dB
Gain Flatness		GSM & CDMA	Tpy= 6dB(P-P); DCS,PCS = 8dB(P-P)
		WCDMA	= 2dB/ 3.84MHz,Full Band = 5dB(P-P)
Noise Figure			= 5dB
VSWR			= 2.0
Group Delay			= 1.5µs
Frequency stability			= 0.01ppm
Spurious Emission & Output inter-modulation			GSM Meet  ETSI TS 151 026 V 6.1.0
			WCDMA Meet 3GPP TS 25.143 ( V 6.2.0 )
			CDMA Meet  IS95 & CDMA2000
WCDMA System		Spurious Emission Mask	Meet 3GPP TS 25.143 ( V 6.2.0 )
		Modulation Accuracy	= 12.5%
		Peak Code Domain Error	= -35dB@Spreading Factor 256
CDMA System		Rho	? > 0.980
		ACPR	Meet IS95 & CDMA2000
Mechanical Specifications			Standard
I /O Port			N-Female
Impedance			50 ohm
Operating Temperature			-25ºC~+55ºC
Environment Conditions			IP40
Dimensions			155x112x85mm
Weight			= 1.50Kg
Power Supply			Input AC90-264V,output DC 5V / 3A
LED Alarm			Standard
Power LED			Power Indicator
UL LED			Be lighted when there is phone calling
DL 1			Be lighted when Outdoor signal is -65dB
DL 2			Be lighted when Outdoor signal only -55dB
DL 3			Be lighted when Outdoor signal only -50dB

The installtion of the Repeater

Outdoor antenna ( for receiving the signal from the BTS ) + Cable ( transfering the received signal) + Repeater ( for amplifying the received signal) + cable( for transfering the amplified signal) + indoor antenna( for shooting the amplified signal),  



(Note : Omni indoor antenna is 3dBi,it can work with about 200m2 . If need repeater coverage larger area , need add more antenna,the HPC-W-27 Max can work with 10pcs indoor antenna.  ( when add antenna ,please remember to take splitters )

Installation steps 

Step 1 Start by taking your phone up to the roof or other location outside to find where the signal is strongest.

Step 2 Temporarily mount the Outdoor (outside) antenna in that location. You may need to adjust and move the antenna later.

Step 3 Run coaxial cable into the building to a convenient loaction (attic, etc.) where you can also get standard power for the Signal Repeater.

Step 4 Place the Signal Repeater in that location and connect the coaxial cable to the Outdoor Side of the Signal Repeater and the Outdoor antenna.

Step 5 Mount your Indoor (inside) antenna in a productive location. You may need to adjust or move the antenna later. More notes on Indoor antennas and patterns here.

Step 6 Connect coaxial cable between the Indoor antenna and the Signal Repeater output port.

Step 7 Power up the system and check for signal inside the building. If needed, tune system by moving and or pointing the Outdoor and Indoor antennas until they get the most signal possible.

Step 8 Secure all antennas and cables, securely mount the Signal repeater and clean up the installation.



Of course there are still a few more things to consider but in general, this is the basic procedure. For more information, please contact us.

Terms and Conditions

Certificate	CE/RoHs
Country of Origin	China
Port of Dispatch	Shenzhen
Production Capacity	1000pcs/month
Date of Delivery	Within 3 days after received payment inform
MOQ	10pcs
Warranty	2years
Pacakge	1pcs/box; 20pcs/carton
Country of Origin	China